Move-In and Move-Out Home Repair Checklist: Room-by-Room Inspection Template
rental-housinghome-inspectionmove-inmove-outrepair-documentationlandlords

Move-In and Move-Out Home Repair Checklist: Room-by-Room Inspection Template

HHandyHome Pros Editorial Team
2026-11-21
7 min read

A room-by-room move-in and move-out checklist for documenting condition, testing systems, comparing wear with damage, and planning repairs.

Use this move-in and move-out home repair checklist to inspect each room, document condition with consistent photos and notes, test essential systems, and separate normal wear from damage that may require repair. The same record can support a renter’s security-deposit discussion, a landlord’s turnover process, a homeowner’s sale preparation, or a post-repair inspection.

Overview

A useful inspection is more than a quick walk-through. It creates a dated record of what was present, working, damaged, missing, or inaccessible at a specific point in time. Complete it at move-in and again before moving out, ideally using the same room order and checklist so the two records can be compared.

Before starting, gather a phone or camera, flashlight, measuring tape, paper or a notes app, and any property condition form supplied by the landlord, property manager, buyer, or seller. If you rent, read your lease and local housing rules before relying on a deadline or deposit procedure; requirements differ by location. Do not sign a condition report that is incomplete or inaccurate. Write “not tested,” “not accessible,” or “needs clarification” when appropriate.

For every issue, record five basic details:

  • Location: room, wall, fixture, appliance, or exterior area.
  • Condition: clean, worn, damaged, missing, leaking, unsafe, or not tested.
  • Evidence: wide photo, close-up photo, video, meter reading, or written note.
  • Date: include the inspection date and, when useful, the time.
  • Follow-up: monitor, report, repair, replace, or obtain a qualified evaluation.

Prioritize hazards over cosmetic defects. Active leaks, exposed wiring, a smell of gas, sewage backup, no heat in dangerous weather, or a nonfunctional smoke alarm should be reported promptly. If you smell gas, leave the property and follow the safety steps in What to Do If You Smell Gas at Home. For water emergencies, use the burst-pipe emergency checklist.

How to estimate

The most reliable way to estimate repair responsibility is to compare three records: the move-in condition report, the move-out condition report, and supporting maintenance communications. A simple decision sequence helps prevent assumptions:

  1. Confirm the baseline. Was the issue documented when you took possession? If so, save the original photo, form, email, or message.
  2. Describe the change. State what is different now, such as a new crack, missing item, broken hinge, stain, leak, or appliance failure.
  3. Classify the issue. Separate ordinary aging and routine maintenance from accidental, negligent, unauthorized, or unexplained damage. The correct classification depends on the agreement and applicable local rules.
  4. Check responsibility. Review the lease, purchase agreement, warranty, maintenance history, and any written instructions before assigning responsibility.
  5. Obtain a scope before a price. Ask a qualified professional to identify the work required. A repair estimate should state labor, materials, access needs, permits if applicable, disposal, and any exclusions.

For a repeatable estimate, use this worksheet:

Estimated total = inspection or diagnostic charge + labor + materials + access or removal + permit or disposal costs + contingency for unresolved conditions.

Do not add a contingency merely to inflate a claim. Use it when the cause is hidden or the professional has identified a reasonable unknown, such as moisture behind a wall or damage beneath flooring. Ask whether the estimate is fixed, time-and-materials, or conditional on opening an area.

When comparing contractors, request the same scope from each provider. A low bid may exclude surface restoration, testing, cleanup, or code-related work. The guide How to Compare Contractor Bids can help organize these differences. For small, defined tasks, use the questions and scope format in How to Hire a Handyman.

Inputs and assumptions

Room-by-room inspection checklist

  • Entry, hallways, and stairs: inspect doors, locks, keys, weatherstripping, flooring, walls, railings, stair treads, lights, and visible ceiling stains. Test door operation without forcing damaged hardware.
  • Living and sleeping areas: photograph floors, carpets, walls, ceilings, trim, windows, blinds, outlets, switches, smoke alarms, and built-in fixtures. Note existing nail holes, scuffs, stains, cracks, or missing covers.
  • Kitchen: check cabinet doors, drawers, counters, backsplash, sink, faucet, drain, garbage disposal if present, outlets, exhaust fan, refrigerator, range, oven, dishwasher, and visible supply lines. Run appliances only according to the manufacturer’s instructions and do not operate an appliance that appears unsafe.
  • Bathrooms: run faucets briefly, check drainage, flush toilets, inspect around the toilet base and under the vanity, test exhaust ventilation, and look for soft flooring, failed caulk, mold-like growth, or water staining. Record slow drainage rather than attempting an invasive repair during the inspection.
  • Laundry and utility areas: inspect washer and dryer connections, shutoff valves, floor drains, water heater surroundings, furnace or heat-pump condition, filters, and visible ductwork. Do not remove panels or work on gas or electrical equipment.
  • Exterior, garage, and storage: inspect siding, doors, windows, foundation-visible areas, gutters, hose connections, driveway, garage door, remotes, fencing, outdoor lights, and provided tools or equipment. Note areas blocked by stored belongings.

Normal wear versus damage

ConditionPossible interpretationWhat to document
Light carpet flattening in a traffic pathMay be ordinary wear, depending on age and conditionWide photo, close-up, and room location
Large burn, cut, or pet-damage areaMay be damage beyond ordinary useMeasured size, close-up, date, and prior condition
Loose cabinet hingeCould be routine maintenance or damageVideo of operation and note whether screws or wood are missing
Water stain or active leakRequires prompt investigation; cause mattersPhoto, moisture or leak details if available, and maintenance report
Faded paintMay result from age, sunlight, or prior workRoom-wide photos and move-in comparison

This table is a documentation aid, not a legal determination. Avoid labeling an item “tenant damage” or “landlord responsibility” until the agreement, evidence, and local requirements have been reviewed.

Worked examples

Example 1: A bathroom leak

At move-in, the inspection form notes a faint stain below the vanity. At move-out, the stain is larger and the cabinet base is swollen. The record should include both dated sets of photos, whether the leak was reported, any maintenance response, and whether the faucet, drain, or supply connection is the source. A plumber can then provide a scope that separates leak repair from cabinet or flooring restoration. Do not estimate responsibility from the final appearance alone.

Example 2: A damaged interior door

The move-in photo shows an intact hollow-core door with a small scuff. The move-out photo shows a punched-through panel and damaged casing. Record the door size, hardware condition, casing damage, and whether matching materials are available. Ask a carpentry or home repair professional whether patching, replacing the slab, or replacing the complete prehung unit is appropriate. Compare estimates using the same scope and include painting or disposal if those tasks are required.

Example 3: An appliance that will not start

First document whether the appliance had power, whether controls were set correctly, and whether a breaker or safety switch had tripped. Note the model number and visible condition, but do not dismantle the appliance. A service technician can identify whether the issue is a supply problem, normal maintenance item, repairable fault, or replacement decision. This approach is more useful than recording only “broken.”

When to recalculate

Revisit this checklist whenever you move, renew a lease, transfer property management, prepare a home for sale, complete a major repair, or discover a new defect. Recalculate a repair estimate when the scope changes, hidden damage is found, materials are substituted, access becomes more difficult, a permit is required, or a contractor’s written assumptions no longer apply.

For a practical closeout, complete these steps:

  1. Save photos and videos in a dated folder organized by room.
  2. Rename files with the location and issue, such as “Kitchen_under-sink_supply-line_2026-11-05.”
  3. Send maintenance requests in writing and retain replies, invoices, and completion photos.
  4. Ask contractors for a written scope, license or qualification details where relevant, insurance information, schedule, warranty terms, and exclusions.
  5. After work, test the affected fixture or system, photograph the result, and record any unfinished items.
  6. For urgent or safety-related findings, use a qualified professional rather than relying on a cosmetic patch.

If an inspection reveals several competing problems, use How to Prioritize Home Inspection Repairs to sort hazards, active damage, essential function, and cosmetic work. Reusing the same inspection record each time creates a clearer maintenance history and gives homeowners, renters, landlords, and contractors a shared basis for decisions.

Related Topics

#rental-housing#home-inspection#move-in#move-out#repair-documentation#landlords
H

HandyHome Pros Editorial Team

Home Improvement Editors

Senior editor and content strategist. Writing about technology, design, and the future of digital media. Follow along for deep dives into the industry's moving parts.